Geely CK MR479Q 2007 Workshop Manual Download Page 348

Page: 348 / 392

341

7.Intermediate Instrument Panel Removal/Installation

(1) Disconnect the negative (--) terminal cable from the battery.

(2) Remove intermediate instrument panel.

(3) Remove the screw.

(4) Using the flat screwdriver wrapped with vinyl tape, disconnect

the clip.

(5) Pull the intermediate instrument panel forward and then remove

the clip.

(6) Remove LDC (Liquid Crystal Display) component connector.

(7) The installation is in the reverse order of the removal.

8.Glove Compartment Removal/Installation

(1) Open the glove compartment;

(2) Pull the glove compartment up and separate it from the instrument panel;

(3) The installation is in the reverse order of the removal.

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands