manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 53

46

1. Avoid fuel ejection

2. Disconnect fuel tank hose

3. Disconnect fuel tank return hose

4. Disconnect fuel tank gas exhaust hose

5. Detach fuel pump assembly with filter screen. See (Figure 103)

Using special tool, loose fuel tank cap. Be careful not to bend the fuel

level sensor arm when pulling out fuel pump.

6. Install fuel pump assembly. See (Figure 104). Replace ring seal .

Align the tab on the fuel pump to the notch on the fuel tank port. Tighten

the fuel tank cap with special tool.

Torque: 40N. m

7. Install fuel gas exhaust hose

(a) Install return hose;

(b) Install fuel hose;

(c) Check fuel for leakage.

Figure 103

Figure 104

New  Washer

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands