manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 177

170

(b) Inspect the stator winding

1

Inspect the resistance of the stator winding

Place the multimeter at R x 1, connect 2 pens of the

meter to any of the 2 pens wires of the armature winding

respectively. There must be continuity. Where the

resistance reading is infinitely great shows an open circuit.

2

Inspect the winding ground

Place the multimeter at R x 1, connect one pole of the

meter to the pole wires of the armature winding

respectively and the other pole of the meter to the stator

core. If the resistance reading is infinitely great, the

armature winding is well-insulated. If not, it needs repairing

and replacing.

IV. ALTERNATOR ASSEMBLY REPLACEMENT (MR479Q, MR479QA, MR481QA)

(a) Disconnect the alternator connector.

(b) Loosen the Bolt A, B, C

(c) Loosen the V-belt. Then remove the alternator.

2. INSTALL ALTERNATOR ASSEMBLY

Torque:

M10 bolt 15N.m (154kgf.cm, 9ft.lbf)

Tension adjustment for V-belt:

When the center of the belt receives a 50N of downward pressure, there is a 10 mm of deflection.

Alternato

r

Inspection of Armature Winding Ground 

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands