Geely CK MR479Q 2007 Workshop Manual Download Page 193

Page: 193 / 392

186

Standard:

Result and solution:

Normal: Repair or replace the harness and connector

If abnormal replace the fuel level sensor

6. THE OTHER INDICATORS

Short the ports of the other indicators respectively to the ground or power source in accordance with the

Circuit Diagram, the indicators will light correspondingly. If it dose not light, replace the combination meter.

If it lights, repair or replace the harness or connector.

7. ODOMETER MALFUNCTION

Inspect first supposing the problem to be from the speedometer. If the speedometer is normal, the combina-

tion meter needs replacing when the odometer is abnormal.

Condition

Standard condition

110±6

Ω

1/2

32.5±3

Ω

3±2

Ω

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands