Geely CK MR479Q 2007 Workshop Manual Download Page 343

Page: 343 / 392

336

2. Retractor

The retractor is pre-tensioner. The retractor will pre-tension the seat belt when something emergency hap-

pens to prevent passengers from being hurt. It can sense the vehicle acceleration and the acceleration of the

belt being pulled out.

The retractor belt can be pull out and drawn back freely. It will not be locked at 12° around the safety

position, but locked at over 27°. The passenger can move in small area. The pre-tensioner will transmit within

5ms~10ms when something emergency happens to tension and lock the belt.

Notice:

1. Check the product for damage, crack and rust before installation.

2. Put the retractor vertically and the belt can be pulled out. Check if the belt can be pulled out

and around. Check if the retractor works.

3. When installing the pretensioned seat belt, check the transmittor head pin for slant and rust.

The transmitter in the pretensioned seat belt can be used for 15 years after installation.

4. Check if the belt buckle and the attachment matches the connecting mode of the to-be-installed

vehicle module. Check if the opening of the buckle is flexible.

5. See if the screw thread of the nut welded on the cover is clear when installing the bolt. Assemble

the bolt after clearing the welding residue if there is any.

6. When the retractor belt is pulled out, there should be no obstacles around the belt (such as,

wire harness ect) , Remove the obstacles and make sure the retractor and the belt will not be

scratched.

3.Front seat belt removal/installation

Warning:

Do not remove retractor.

(1) Turn the ignition switch to LOCK.

(2) Disconnect the negative (--) terminal cable from the battery

for 1min.

(3) Remove B- pillar lower frame.

(4) Pry the seat belt which is used to install the tension wheal.

Use a screwdriver to pry off the stop plate of the seat

belt connector with tensioner.

(5) Disconnect the seat belt connector with tensioner.

Remove 2 set bolts on the hang ring and remove the hang

ring.

(6) Remove two set bolts in the retractor and remove the

front seat belt.

(7) The installation is in the reverse order of the removal.

Stop Plate

Bolt

Front Seat Belt

Screw

Bolt

Lid

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands