Geely CK MR479Q 2007 Workshop Manual Download Page 308

Page: 308 / 392

301

4. Heater

Figure 5 Heater Door Control Diagram

The heater comprises the heater radiator (heat exchanger), the plastic case forming the air duct, connecting

rods adjusting different air ducts and the door. The two groups of combination doors in the heater case are

connected to the heating control mechanism by the cable. The first group is the two couple action doors

adjusting the air mix ratio that are located in the outlet and inlet each; the second group comprises 4 doors

controlling the air outlet vents, where the upper center one controls the front outlet vent, each of the upper

left and right sides controls a defogger outlet vent and lower foot outlet vent. Figure 5 shows the working

principle of temperature adjustment door. The d) , c) , e) , f) in the figure indicate the outlet air flow direction

as the result of the adjustment of the control knob in the heating control mechanism panel.

Hot Wind Location

Cold Wind Location

Linkage

Radiator Core

Temperature Adjustment
Door Working Principle

Foot Outlet

To Front Outlet

To Defroster

Radiator Core

To Front Outlet

Radiator Core

Foot Outlet

To Defroster

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands