manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 123

116

Chapter 6 Rear Suspension System

Section 1 Rear Suspension System

Rear suspension structure description

This model uses strut independent rear suspension with stabilizer bar.

Rear suspension consists of the parallel front and rear double transverse arms, trailing rod, rear stabilizer bar

and rear strut assembly. The shock absorber and cone coil spring are arranged eccentrically.

See the table below for the major technical parameters of the rear suspension

Problem Symptoms Table

Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely

cause of the problem. Check each part in order. If necessary, replace these parts.

Items

Parameter

Items

Parameter

Shock absorber operating

cylinder diameter /mm

￠

56

Camber

-20´±30´

Shock absorber piston rod

diameter/mm

￠

18

Wheel toe-in/mm

1

～

5

Shock absorber stroke/mm

230mm

Remark: Wheel alignment parameter is at free load

Symptom

Suspected Area

1. Tires (Worn or improperly inflated)

2. Wheel alignment (Incorrect)

3. Hub bearing (Worn or damaged)

4. Suspension parts (Worn or damaged)

1. Vehicle (Overloaded)

2. Spring (Stiffness small)

3. Shock absorber (Worn)

1. Tire (Worn or improperly inflated)

2. Wheel (not within specification)

3. Shock absorber (Worn)

1. Tire (Worn or improperly inflated)

2. Wheel alignment (Incorrect)

3. Shock absorber (Worn)

4. Wheel (not within specification)

1. Tire (Worn or improperly inflated)

2. Wheel alignment (Incorrect)

3. Shock absorber (Worn)

4. Suspension parts (Worn)

Abnormal tire wear

Deviation

Body Descent

Sways

Rear wheel shimmy

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands