Geely CK MR479Q 2007 Workshop Manual Download Page 204

Page: 204 / 392

197

III. WIPER SWITCH ASSEMBLY REPLACEMENT

1. DETACH STEERING WHEEL ASSEMBLY

(a) Disconnect the main power source of the vehicle.

(b) Remove the passenger SRS module assembly, and cautiously put it in a safe place.

2. REMOVE WIPER SWITCH

(a) Disconnect the connector.

(b) Remove the 2 tapping screws that are for mounting the wiper switch, take out the wiper switch from the

bracket of the combination switch.

IV. WASHER NOZZLE

ADJUSTMENT

1. INSPECT WASHER NOZZLE

(a) Start the engine, check if the position where the washer fluid from the nozzle sprays the windshield is in

the central or upper of the area wiped by the blades.

(b) Change the direction (horizontal) of the nozzle hole to adjust the point where washer fluid sprays the

windshield.

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands