manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 147

140

Section 2 Brake Fluid

Bleeding

1. Fill brake reservoir with brake fluid

Brake fluid:  JG4 GB10830

2. Bleed brake pipeline system

(1) Connect the vinyl pipe to the wheel cylinder bleeder plug port

(2) Depress the brake pedal several times, and then loosen the bleeder plug with the pedal held down.

(3) At the point when fluid stops flowing out, tighten the bleeder plug, and then release the brake pedal.

(4) Repeat (2) and (3) until all the air in the fluid has been bled out.

(5) Repeat the above procedure to bleed the brake pipeline of the air for each wheel cylinder.

Notice: Fill brake fluid into the reservoir all the time when bleeding.

3. Check fluid level in reservoir

Check the fluid level and fill fluid if necessary.

Symptom

Suspect area

1. Wheel cylinder piston (stuck)

2.  Brake shoe lining (oily)

3. Disc (scratched)

4.  Brake shoes or lining (cracked or distorted)

5.  Wheel hub bearing (worn or damaged)

Tire pressure (not as specified)

1.  Brake shoe lining (damaged)

2.  Installation bolt (loose)

3.  Disc (scratched)

4.  Brake shoe (bad in quality)

5.  Brake shoes lining (oily)

6.  Sound isolating shim damaged

7.  Hold spring of brake shoe (damage)

 Brake Deviation

Noise from brake

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands