manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 301

294

III.  HCU Replacement

1. Depress the retaining clip on the union joint side

and remove the cylinder motor wire harness.

2. Remove the 4 screws as shown in the figure, the

removed old screw can not be reused.

3. Separate the HCU from the ECU.

4. Install the new HCU to the ECU.

5. Use new screw to attach the ECU to the HCU,

tighten the torque: 3+1Nm.

6. Connect the motor wire harness, be careful that

the retaining clip shall be in place.

IV. ECU Replacement

1. Depress the retaining clip on the union joint side and remove the

wire harness.

2. Remove the 4 screws as shown in the figure and discard them

3. Remove the HCU from the ECU.

4. Install the new ECU to the HCU.

5. Use the new screw to attach the ECU to the HCU, tighten the

1Nm.

6. Connect the motor wire harness, be careful that the retaining clip

shall be in place.

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands