Geely CK MR479Q 2007 Workshop Manual Download Page 138

Page: 138 / 392

131

Replacement

1. Cautions (refer to Steering System Cautions)

2. Make sure the wheels are placed straight ahead

3. disconnect the battery negative terminals

4. Remove the air bag assembly

Remove two screws on both sides and pull out the wiring harness connector

Notice: Do not pull air bag wire harness when removing the air bag assembly!

Warning:

Make sure the upper surface of the air bag assembly is kept upward when placing it!

Do not disassemble the air bag assembly!

5. Remove steering wheel assembly

(1) Remove the nut.

(2) Remove the steering wheel cover set bolt.

(3) place the matchmarks on the steering wheel and main shaft assembly.

(4) Use special tool to remove the steering wheel assembly.

6. Remove the steering column upper and lower cover

(1) Remove 3 screws.

(2) Remove the steering column upper and lower cover.

Use Inner

Hex Socket

Wrench

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands