manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 107

100

(3) Check the Rzeppa Constant velocity universal joint for looseness

(4) Check the boot for damage

Notice: Check that the propeller shaft assembly is placed horizontal.

8. Disassemble the tripod constant velocity universal joint boot Use screwdriver to loose the tripod constant

velocity universal joint boot band, remove the boot

Notice: Replace the band if it is distorted

9. Disassembly the tripod constant velocity universal joint

(1) Remove the old grease

(2) Use the mark pen to place a matchmark on the inboard and outboard joint

Notice: Do not punch the marks

(3)

Remove the outboard knuckle

(4)

Use snap ring pliers to remove the snap ring

(5)

Use mark pen to place matchmarks on the tripod ball joint and outboard joint

(6)

Use brass bar and hammer to remove the tripod ball joint

Notice: Do not tap the roller

Mark

Brass Bar

Mark

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands