Geely CK MR479Q 2007 Workshop Manual Download Page 169

Page: 169 / 392

162

2. INSPECT STARTER NO-LOAD

(a) Connect the magnet exciting coil and the terminal.

(b) Connect the ammeter and the battery to the starter

as shown.

with the clutch pinion gear moving out.

(d) Check that the ammeter shows the specified

current.

Specified current: 90 A or less at 11.5 V

if the current is not normal, replace the starter.

3. WIRING

(a) Check that the connecting wire between

the positive (+) and the starter is stable

and reliable, and the insulating bush is in

good condition, in order to avoid a fire

caused by electric spark.

(b) Check that there is continuity in the wire

and if the insulating bush is not damaged.

If the harness is damaged, replace it.

Ammeter

Ignition Switch

Battery

Main Fuse Box

Starter

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands