Geely CK MR479Q 2007 Workshop Manual Download Page 291

Page: 291 / 392

284

Note: This fault only applies to the condition that the system can communicate with the scan

meter (ABS ECU Power supply is normal), and there is no DTC set.

2 After the engine is started, ABS

Warning Light is normally on

Likely Causes

[Description]

One of the Likely Causes is that

ABS warning light drive module is damaged or

there is an open in the ABS warning light

circuit.

The warning light drive module is damaged

ABS warning light drive module circuit open

ABS ECU is damaged

Repair the wire harness

Check whether there is an open circuit in the wire be-

tween the ECU and ABS warning light drive module

Check the ABS warning light drive module

Replace

Abn.

Yes

Replace the ABS ECU

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands