manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 257

250

(2) Trouble indication

1

In case of a trouble, the warning light will indicate. If the external trouble is a history trouble, the indication

will be cancelled. When the history trouble happens for no less than 5 times, the indicator light will remain

on even if there is no more trouble. "Low battery voltage" shall not be counted in the total number of

troubles.

2

Only a service worker can reset a displayed or history trouble. The internal troubles of a SRS ECU

(HAE2.5) or the "crash record" of a trouble cannot be reset, in which case the SRS ECU (HAE2.5) shall

be replaced.

(3) Microcontroller-independent warning light on

Microcontroller with definitive troubles cannot fulfill its functions, thus cannot control the warning light. In

this case, the warning light will light up through proper circuit regardless of the microcontroller as stated

below:

Malfunction of the battery supplying power to SRS ECU (HAE2.5): the warning lights are turned

on continuously by means of the drive function of the selfcheck light.

Loss of internal working voltage: the warning light remains on.

Reset due to trigger failure of the watchdog: the warning light blinks.

Microcontroller out of work: the warning light always lights up.

Incomplete insertion of SRS ECU (HAE2.5) connector: the warning light remains on by means of

a shorting bar.

The diagnostic procedures can well be illustrated as follows:

If it is found that the SRS warning light remains on, follow the undermentioned procedures to check even if

the light goes out eventually. First, a scan meter is used to check the location of the trouble.

Then£¬go on with the checking in accordance with specific methods and procedures for the correspondent

location.

a. If the result indicates that it is an internal trouble or that the SRS is already detonated, replace the

ECU directly.

b. Troubleshooting.

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands