Geely CK MR479Q 2007 Workshop Manual Download Page 315

Page: 315 / 392

308

Section 6 Basic System

1. Blower Removal / Installation

1. Disconnect the negative (--) terminal cable from the battery.

2. Remove instrument panel.

3. Remove motor connector.

4. Remove the resistor connector.

5. Remove the band.

6. Remove bolt. Remove blower.

7. The installation is in the reverse order of the removal.

2. Heater Removal / Installation

1. Remove water hose No. 1 and 2.

2. Remove instrument panel.

3. Remove the band.

4. Remove 2 wind door cables.

5. Remove heater.

6. The installation is in the reverse order of

the removal.

3. The Evaporator Removal / Installation

1. Remove evaporator inlet and outlet pipeline.

2. Remove instrument panel.

3. Remove thermistor connector.

4. Remove 2 bands.

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands