Geely CK MR479Q 2007 Workshop Manual Download Page 369

Page: 369 / 392

362

(II) Floor Assembly

Floor assembly is the base of the main body and an important structure component to link with assemblies

and for load transfer and bearing. The vehicle running performance depends on its intensity and rigidity.

Figure 5-3 is the dismantle diagram of the floor parts.

Floor assembly is composed of front floor assembly and rear floor assembly. A protrusile tunnel runs longitu-

dinally in the center of the front floor. The tunnel and the lower floor rail can strengthen its rigidity in

longitudinal direction. The lower space of the tunnel is used to mount components such as transmission shift

pull rod, park brake drawing cable, exhaust pipes with 3-way catalytic converter. Carpet and sound insulator

mat are mounted in the inner side of the compartment. The first and the second cross member, LH/RH side

member and side rails which are on the front floor form a frame structure. It can provide great load-bearing

capacity to assure strict running requirements for body.

Figure 5-3 Decomposition Diagram of Floor Parts

1 LH/RH Front Floor Side Rail 2 Front Floor

3 Front Floor Cross Member

4 LH/RH Floor Side

Member

5 Rear Floor 1st Cross Member 6 LH/RH Rear Floor Side Rail

7 Rear Floor 2nd Cross

Member Assy.

8 Rear Floor

Front

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands