manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 259

252

(3)Check the connection between ECU and instrument cluster

1

Turn the ignition switch to LOCK.

2

Disconnect the negative (-) terminal cable from the battery.

3

Disconnect the connector of instrument cluster.

4

Check if the related circuits of the warning light are connected or not.

Yes: continue with next step.

No: replace the wire harness, and then continue with step 5.

2. SRS warning light remains on.

DIAGNOSTIC PROCEDURES

To begin the check, first use special diagnostic instruments and ECU to perform communication diagnosis

and find out the causes of the trouble. If the communication fails, continue with the following procedures:

(1) Check battery

1

Check battery voltage.

2

Is voltage higher than 9V?

Yes: continue with next step.

No: Insufficient battery supply. Check the charging/discharging system, and then continue with step (5).

(2) Check the continuity of the wire harness between ECU and instrument cluster

1

Turn the ignition switch to LOCK.

2

Disconnect negative (-) terminal cable from the battery.

3

Open the guard plate of the central passage.

4

Disconnect the connector of the instrument cluster.

5

Connect the negative (-) terminal cable of the battery.

6

Turn the ignition switch ON.

7

Check whether the voltage of the connector terminal of the instrument is 12V (power supply and instrument

connecting wire).

Trouble

Checking Status

Possible Cause

 

Insufficient battery supply

 ECU internal trouble

 SRS warning light trouble of instrument cluster

 Improper connection of ECU connector

 

Poor contact of instrument cluster connector

 Open circuit or poor contact of ECU power supply fuse

 

Poor connection of ECU connector terminal

 Poor contact of the wire harness between ECU

connector terminal and ground

 Driver or passenger side circuit trouble of SRS

SRS warning light

remains on

SRS warning light

remains on

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands