manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 168

161

Chapter 2 Starting and Charging System

Section 1 Starting System

(MR479Q MR479QA MR481QA)

I. STARTER INSPECTION

NOTICE:

These tests must be done within 5 seconds to avoid burning out the coil.

1. INSPECT MAGNETIC SWITCH

(a) Use wire to connect the starter as shown.

(b) Connect the magnetic switch and the battery as

shown.

(c) Disconnect the magnet exciting coil from the

terminal A.

(d) Check if the clutch pinion gear is moving out.

If the clutch pinion gear is not moving out, replace

the magnetic switch.

(e) Connect the battery as shown above. Disconnect

the battery positive (+) from the terminal, to make the clutch pinion gear disengaged.

(f) Check if the clutch pinion gear has returned.

If the clutch pinion gear has not returned, replace

the magnetic switch.

Terminal A

Battery

Battery

Disconnect

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands