Geely CK MR479Q 2007 Workshop Manual Download Page 330

Page: 330 / 392

323

1. Front Bumper Removal and Installation

(1) Disconnect the negative (--) terminal cable from the battery. Disconnect fog lamp wire;

(2) Remove the mudguard skirt to front bumper clip;

(3) Remove the attaching bolt of the the front fender and panel and the front bumper sub-assembly;

(4) Remove the front bumper set screw and the clip. Remove the front bumper mounting plate and the

positioning screw of the seat;

(5) Remove the bolt which connecting front bumper mounting bracket with the vehicle body;

(6) Pull the front bumper assembly and the secondary bumper assembly together out of the vehicle body.

Separate the front bumper mounting bracket from the rail, front bumper mounting plate from the front

bumper mounting plate seat;

(7) Remove the front bumper mounting plate seat from the vehicle body;

(8) Remove the secondary bumper assembly and the front bumper mounting bracket sub-assembly;

(9) Remove front bumper mounting plate;

(11)Remove front bumper cushion. Remove the front license plate. Remove the mounting plate assembly;

(12)Remove fog lamp;

(13)The installation is in the reverse order of the removal.

2.Notice For Removal Of The Front Bumper

(1) Pull the front bumper to separate it from the bumper rail.

(2) Uniformly pull it by force to prevent the front bumper mounting plate and seat from damage.

Warning

If the front bumper is only separated from the bumper rail on one side, the bumper may drop

and result in body hurt. Be careful not to drop the bumper when separating the front bumper

from the bumper rail.

3.Notice for installation of the front bumper

(1) Press the front bumper connecting part to the vehicle body and connect the rear bumper mounting

bracket assembly with the bumper rail.

(2) Be sure to insert the front bumper mounting plate seat into the bumper mounting plate.

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands