manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 335

328

1.Rear trunk Lid Removal/Installation

Warning

It is dangerous to remove the rear trunk lid spring before supporting the rear trunk lid. The rear
trunk lid may drop and result in body injury. Fully open the rear trunk lid, support the rear trunk
lid before removing the brace.

Remove rear trunk lid under the help of the assistant.

(1) Disconnect the negative (--) terminal cable from the battery;

(2) Disconnect rear trunk wire harness connector. Pull the rear trunk lid wire harness out from the rear

trunk;

(3) Remove rear trunk door lock cylinder assembly. Pull out the rear trunk door lock cable;

(4) Remove rear trunk lid spring;

(5) Remove rear trunk lid hinge connecting bolt. Remove the rear trunk lid;

(6) Remove rear trunk lid hinge seat mounting nut. Remove the rear trunk lid hinge seat and the rear trunk lid

hinge

(7) Remove rear trunk door oil filler cable assembly;

(8) Remove cushion;

(9) Remove rear trunk lid hinge pin. Remove rear trunk lid hinge from the bracket;

(10)

Remove rear trunk lid weatherstrip;

(11)

Remove rear trunk lid inside trim board clip, Remove rear trunk lid inside trim board;

(12)

Remove rear license plate assembly mounting nut , Remove rear license plate assembly;

(13)

The installation is in the reverse order of the removal.;

(14)

Adjust the rear trunk lid. (See rear trunk lid adjustment)

2.Rear trunk Lid Adjustment

(1) Measure the clearance and height between the rear trunk lid and vehicle body.

(2) Loose the rear trunk lid hinge mounting bolt or the rear trunk latch mounting screw and reinstall the rear

trunk lid if it is not as specified.

Clearance

a: 3.74mm

b: 1.0mm

c: 4.0mm

(3) Tighten the rear trunk lid hinge bolt;

(4) Close the rear trunk lid

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands