manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 135

128

Chapter 8 Power Steering System

Section 1 Power Steering System

Power Steering System Description

Power Steering System consists of the steering wheel, steering transmit device, power steering fixed device

and steering pipelines. The steering gear is rack and pinion type.

Major parameters for steering system:

Cautions:

1. Cautions for steering system

Make sure of the correct replacement of parts, incorrect replacement might affect the performance of

the steering system and lead to driving accidents.

2. Cautions for SRS System

This vehicle is equipped with SRS (Supplemental Restraint System), driver side air bag and front passenger

side air bag.

Failure to carry out service operations in the correct sequence could cause the unexpected deployment of

the air bag during servicing, possibly leading to a serious accident.

Parameter

 3.26

Inner                      37.6°

Outer                      33.3°

 

≤

10.5m

Item

Steering Wheel total revolutions

Maximum Front

Wheel Turn Angle

Minimum Turning Diameter

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands