Geely CK MR479Q 2007 Workshop Manual Download Page 249

Page: 249 / 392

242

Chapter 7

SRS (Supplemental Restraint System)

Section 1 SRS-General Information

I. PRECAUTION

For safe reasons, read the following precautions before starting any operation.

1. When servicing the SRS, correct sequence and items are described in the following chapter.

2. Instruments and special tools recommended in this chapter shall be used for operation.

3. When servicing the following components, replace them with the new ones if there is a failure.

(1) SRS ECU

(2) Clock Spring Module

(3) Driver Airbag Module

(4) Passenger Airbag Assembly (Option)

4. If there is any abnormality in the wire harness of the SRS, replace it with a new one. Correct or replace the

abnormal wire harness in accordance with Table 1.

Figure 1

(Table 1)

Designation

Description

Belt-pretensioner, Driver, Low

Seat belt pretensioner, driver side, low position

Belt-pretensioner, Driver, High

Seat belt pretensioner, driver side, high position

Belt-pretensioner, Passenger, High Seat belt pretensioner, passenger side, high position

Belt-pretensioner, Passenger, Low Seat belt pretensioner, passenger side, low position

IGN

Battery voltage

GND

Ground-ground wire

Airbag warning light

Diagnostic serial data I/O (K line)

DAB Hi

Driver airbag, high position

ECU Terminal Description

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands