3-216
UR FAMILY – COMMUNICATIONS GUIDE
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
CHAPTER 3: IEC 61850 COMMUNICATION
3
InjAmp
MV
Injected current.
SH INJECTION AMPS in amperes.
SubHaPHIZ
InjVol
MV
Injected voltage.
INJECTED VOLTAGE in volts.
SH INJECTION VOLTS in volts.
FldGnd0PHIZ, SubHaPHIZ
InService
SPS
LED indication - Relay In-service. The LED IN SERVICE operand.
LEDsIHMI
IntermSt1
SPS
Intermediate-status detected.
The BREAKER/SWITCH INTERM operand.
Bkr
Θ
XCBR, Disc
Θ
XSWI,
GGIO3
IntrAlm
SPS
Indicates that the current exceeded the maximum interrupting current rating
during the last interruption event.
The BKR ARC 1 MAX OP operand.
CBArc0SCBR
IntrAlmDpo
SPS
Inverse of IntrAlm.
The BKR ARC 1 MAX DPO operand.
CBArc0SCBR
IrigbFail
SPS
A bad IRIG-B input signal has been detected.
The IRIG-B FAILURE operand.
LPHD
IsoBlk
ACT
B90 - Indicates that the isolator position is invalid
B_IsoSSWI
IsOn
SPS
Indicates the time of day timer is on.
The TIME OF DAY 1 ON operand.
TmDayGAPC
IsoPos
ACT
B90 - Indicates position of isolator. When "On", the related current is included in
differential zone; when "Off", the current is excluded from differential calculations.
B_IsoSSWI
LastClrTm
INS
Represents the UTC time of user fault reports last cleared time in seconds elapsed
since 1970/01/01, 00.00.00.
The LAST CLEARED DATE actual value.
UFlt0RFLO
LastRptTm
INS
Represents the UTC time of last user fault report generated time in seconds
elapsed since 1970/01/01, 00.00.00.
The LAST REPORT DATE actual value.
UFlt0RFLO
LastSqNum
INS
Last sequence number received.
Actual value RxGOOSE1 SqNum.
LGOS
LatchErr
SPS
A difference is detected between the wanted and actual latch contact state.
The LATCHING OUT ERROR operand.
LPHD
LeoSt
SPS
Line end open status.
The LINE PICKUP LEO PKP operand.
LinPkpPIOC
LivDea
SPS
This data object indicates that live/dead conditions have been met.
The SYNC 1 DEAD S OP operand, which indicates that live/dead conditions have
been met.
SynChkRSYN
LivDeaDpo
SPS
This data object indicates that live/dead conditions have not been met.
The SYNC 1 DEAD S DPO operand, which indicates that live/dead conditions have
not been met.
SynChkRSYN
LivLiv
SPS
This data object indicates that both sources are live, and that angle, frequency,
and voltage difference and range conditions have been met.
The SYNC 1 SYNC OP operand, which indicates that both sources are live, and that
angle, frequency, and voltage difference and range conditions have been met.
SynChkRSYN
LivLivDpo
SPS
This data object indicates that one or both sources are not live, or that angle,
frequency, and voltage difference and range conditions have been met.
The SYNC 1 SYNC DPO operand, which indicates that one or both sources are not
live, or that angle, frequency, and voltage difference and range conditions have
been met.
SynChkRSYN
LivV1
SPS
This data object indicates that V1 is above the LivVal1 setting.
The SYNC 1 V1 ABOVE MIN operand, which indicates that V1 is above the LivVal1
setting.
SynChkRSYN
LoadDev
MV
Indicates the motor load standard deviation at the time of the broken rotor bar
data acquisition stage.
LOAD DEV. AT BRB CALC. in x FLA.
BknRotSVBR
LocCmdAcsOff
SPS
Indicates operations of FlexLogic operand ACCESS LOC CMND OFF
SecGSAL
LocCmdAcsOn
SPS
Indicates operations of FlexLogic operand ACCESS LOC CMND ON
SecGSAL
LocMod
SPS
Capacitor control in local mode.
The CAP 1 IN LOCAL operand.
CapCtlGAPC
Data object
name
CDC
Semantics
Used in logical nodes…
