FUTABA 01000141 Full Manual Download Page 16

Page: 16 / 225

Power OFF

Power ON

Throttle Stick Low

Power Switch

Long Push

Push

1. Turn on the transmitter power switch.

2. Turn on the receiver or speed control power switch.

Always be sure the motor/engine is stopped.

1. Turn oﬀ the receiver or speed control power switch.

2. Then turn oﬀ the transmitter power switch.

OFF

Turning on the power switches

If the power switches are turned oﬀ in the opposite order the model may unexpectedly run out of control and

cause a very dangerous situation.

Turning off the power switches

How to turn transmitter power ON/OFF

When turning on the power, the T16IZ transmitter will begin emitting RF automatically after it confirms

the surrounding RF conditions. The status of the transmitter is displayed by LED at the upper part of the

front of a T16IZ.

*If THR stick is high, a WARNING screen will appear. Another warning will appear if a power

supply is attached. (In Multicopter mode, the THR position alarm will not appear.)

If the "Thr position" alarm displays

*If the throttle stick is in the high position when the

power is turned ON

Warning alarm

Tap this to stop the alarm

and RF signal. Only panel

screen operation is active, the

transmitter will not link to any

receiver.

When the alarm activates, lower the throttle stick

before turning the receiver power ON.

*If the power is turned ON when the idle-up, air brake,

etc., switches are ON, the above warning will display.

Ensure the relevant switches are turned OFF.

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands