FUTABA 01000141 Full Manual Download Page 63

Page: 63 / 225

● Long press the [U.MENU/

MON.] button in the

Home screen to call the

setup screen shown.

＜ or ＞

Each channel movement can be checked.

Select the [OFF] or pushing the

HOME/EXIT button → Testing is

stopped

[Neutral]: Mode which locks each servo in the

neutral position

[Moving]: Mode which repeats operation of

each servo

Servo monitor

Servo Test & Graph Display / Displays servo positions.

This is used for testing servo movement. “Moving

Test” (repetition mode) and “Neutral Test” (fixed

position mode) are available.

The “Neutral Test” is good for finding the neutral

position of a servo horn.

In order to prevent any potential difficulties,

the servo test function will be inoperable, or

inaccessible, under certain conditions. Specifically,

the Servo Test function is not operational if the

Throttle cut is ON in either airplane or helicopter

modes; or if the Throttle hold is ON in helicopter

mode.

● Select [Servo monitor] at the linkage menu and

call the setup screen shown below.

WARNING

Don't set a servo test mode when the

drive motor is connected and the engine

has been started.

■Inadvertent rotation of the motor or acceleration of the engine

is extremely dangerous.

Test mode change :

OFF → Neutral → Moving

●Return to Home or

Linkage menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands