FUTABA 01000141 Full Manual Download Page 61

Page: 61 / 225

Fix and return to an

information screen.

Movement of a cursor of an input box

Input box

The program version and SD card size are displayed. The User name,

language and Unit system used by the system can also be changed.

*If an SD card is not inserted, no memory card information

will be displayed.

The Information screen displays the T16IZ system

program version information, SD card (memory

size, card free size) information.

● Tap the [Information] button at the System menu

to call the setup screen shown below.

●Return to System menu

Information

Telemetry numerical values can be displayed in

either metric or SAE (yard-pound) units.

This function registers the T16IZ user name and the

language displayed at proportional can be changed.

Registration of the user's name

T16IZ transmitter can register user's name.

How to register user's name

1. Turn on the power of the transmitter.
2. Select "user's name" and then the keyboard

will pop up.

3. You can use up to 15 characters as a user's

name. Use the keyboard on the screen to

enter user's name.

Back space (Input box)

2/2 : WEB Manual QR code

Next page

(Character list 2/4 - 4/4)

An input box is reset

The language displayed at proportional can

be changed. The initial setting is English, but

different languages can be selected.

[Metric]

Distance --- m (meter)

Speed --- km/h (kilometers per

hour)

Variometer --- m/s (meter per

second)

Temperature --- ℃ (centigrade)

[Yard]

Distance --- yard

Altitude --- feet

Speed --- mph (mile per hour)

Variometer --- fpm (ft per min)

Temperature --- ℉ (fahrenheit)

Telemetry Display Unit

1/2

Shift key

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands