FUTABA 01000141 Full Manual Download Page 118

Page: 118 / 225

118

Data reset

Model memory setting data reset. (by item)

This function is designed to allow you to reset

selected portions or all of the settings saved in

the active model memory. You may individually

choose to reset the following sets of data:

Trim (All condition):

Reset the digital trim setting.

*All the conditions, or the condition currently

being displayed (the entire group for group setting),

can be selected.

*The trim step amount and trim rate are not reset.

Trim (Current and Group condition):

Reset the digital trim setting.

*Current condition, group condition, can be

selected.

Data resetting method

1. Tap to the item you want to reset and tap

the screen.

*A confirmation message appears.

*The trim step amount and trim rate are not reset.

Model menu setting:

Resets all the functions in the Model menu except

condition select.

All model setting:

Resets all Linkage and Model menu functions

except for system type, model select, model type,

function name, and telemetry setting.

Function Name:

A function name is reset.

Telemetry:

Reset the telemetry setting.

[Trim (All condition)]: Resets only the Trim (all

conditions)

[Trim(Current and Group condition)]: Resets

only the data of Trim (condition in use and all

the conditions set to group mode)

[Model menu setting]: Resets all the functions

in the model menu, except the condition

selection functions.

[All model setting]: Resets all the functions in

the linkage menu and model menu except

the frequency, model select, and model

type functions.

[Function name]: Resets only the function

name functions.

[Telemetry]: Resets only the teremetry

functions.

2. Execute reset by tapping the "Yes".

● Select [Data reset] at the linkage menu and call

the setup screen shown below.

CAUTION

Throttle Reverse

■ Only the throttle channel (CH3) initial setting is

REV (reverse). Thoroughly check the Hi and Low

directions of the engine or motor used and be careful

that they do not suddenly run at full speed. Even

after data reset, CH3 is reversed

CAUTION

Never engage the Data reset function

while the engine is starting or the

motor drive wiring is connected.

■ Sudden, abrupt spinning of propellers or rotors is

extremely dangerous.

●Return to Linkage menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands