FUTABA 01000141 Full Manual Download Page 82

Page: 82 / 225

Neutral point setting procedure

*Becomes the compensation reference point.

*Adjusting the servo horn so that the neutral point position is

near the 50% position makes the mixing amount small.

1. Hold the servo horn at a right angle to the

linkage rod, and then tap the [Enter] button

and read the actual neutral point.

*The neutral point is displayed on the screen.

After reading this neutral point, use other

compensation functions to make further

adjustments.

To exit the setting, tap the [Swash] button.

Swash AFR setting procedure

Adjust so that the specified operation

amount is obtained by aileron, elevator, and

pitch operation.

1. Tap the button of the AFR rate to be

adjusted. Value input buttons appear on the

screen.

2. Use the value input buttons to adjust the AFR

rate.

Initial value: +50%
Adjustment range: -100%~+100%

+or- the direction of operation changes.

To exit setting, tap the [Swash] button.

Mixing rate setting procedure

HR-3 is described as an example. The mixing

applied in other swash modes is different, but

the setting procedure is the same.

1. Set the throttle stick to the set neutral point.

Adjust the length of the linkage rod so that

the swash plate is horizontal at this position.

*A little adjustment using sub trim should be OK.
*Adjust so that pitch operation when the pitch curve

is straight is maximum.

2. Adjust the AIL->PIT amount so there is no

interference in the elevator or pitch direction

when the aileron stick is moved to the left

and right.

*Adjust the left and right sides separately.

3. Adjust the ELE->AIL and ELE->PIT amounts so

there is not interference in the aileron or pitch

direction when the elevator stick is moved

up and down.

*Adjust the up and down sides separately.

4. Adjust the PIT->AIL and PIT->ELE amounts so

that the swash plate is horizontal when the

throttle stick is set to maximum slow and full

high.

*Adjust the slow and high sides separately.

To exit setting, tap the [Swash] button.

Linkage correction setting procedure

*Set the linkage compensation after setting the mixing

rate.

*This function compensates for elevator interference

by aileron operation or aileron interference by

elevator operation at Low pitch and Hi pitch at

collective pitch (HR3, etc.) control.

1. Set the throttle stick to the maximum slow

position. Move the aileron stick to the left and

right and adjust the aileron compensation

amount so that interference in the elevator

or pitch direction at that time is minimal.

*The left and right sides can be adjusted separately.
*If the interference increases when the compensation

amount is increased, make the compensation

direction "-".

2. Adjust the elevator compensation amount

so that the interference in the aileron or pitch

direction when the elevator stick is moved

up and down is minimal.

3. Perform aileron and elevator compensation

similarly for the throttle stick full high side.
To exit setting, tap the [Swash] button.

Speed compensation setting procedure

1. Set the throttle stick to the neutral point

position. Move the elevator stick quickly and

adjust the speed compensation amount so

that the interference in the pitch direction is

minimal.
To exit setting, tap the [Swash] button.

Notes:
If the linkage is too long or short, correct

compensation will not be applied. Correct

this before continuing. The pitch angle

changes after any adjustment. Reset the

pitch angle when actually flying after

compensation processing.

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands