FUTABA 01000141 Full Manual Download Page 90

Page: 90 / 225

Sensor：Reload

● Call page 3/3 from the [Sensor] menu.

This page is set when using multiple telemetry sensors of the same type.

When using multiple sensors of the same type

the sensors must be registered in the transmitter.

Connect all the sensors to be used to the T16IZ as

shown in the figure at the right and register them by

the following procedure. The ID of each sensor is

registered in the transmitter.

Hub

SENSOR

Reading all the sensors to be used

1. Connect the sensor to the T16IZ as shown in the figure above.

2. Tap “Reload” on page 3/3 of the [Sensor] screen.
3. Tap “Reload”.
All the sensors are registered and can be used.

*It is not necessary to carry out

multiple battery connections like

a T18MZ/T14SG.

Sensor : Register

This page is set when using multiple telemetry sensors of the same type.

This function registers an additional sensor.

Connect the sensor as shown in the figure at the

right and register it by the following procedure.

The sensor ID is registered in the transmitter.

SENSOR

Additional sensor registration

1. Connect the sensor to the T16IZ as shown in the figure above.

2. Tap “Register” on page 3/3 of the <Sensor> screen.
3. The sensor is registered and can be used.

*When the number of slots needed in registration is insufficient, an error is

displayed and registration cannot be

performed. Disable unused slots or

perform the following reload.

● Call page 3/3 from the [Sensor] menu.

●Return to

Linkage menu

●Return to

Linkage menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands