manualshive.com logo in svg

FUTABA 01000141, Full Manual

FUTABA 01000141 is a revolutionary product designed for convenience and efficiency. With its full manual available for download, users can easily access the comprehensive instructions they need to make the most out of their purchase. This manual can be downloaded for free from manualshive.com, ensuring hassle-free and user-friendly experience.

Share
Download
background image

186

 

Flight Tune（Aileron / Elevator Basic settings）

 

Flight Tune（Aileron / Elevator Basic settings）

Note

:

 

To effectively operate the next "ELE Comp" 

(elevator correction), make sure to set "Pit High", "Pit 
Zero", "Pit Low" on the "SWASH BASIC" menu.

(7) ELE. Comp: Elevator pre compensation   

A helicopter that has a head that rotates clockwise, will exhibit a tendency 
whereby the nose will be pulled towards the disk with positive blade pitch.   
Conversely, the helicopter will push the nose away from the rotor disk dur-
ing negative pitch inputs.  In an instance of a slower servo set-up or larger 
(heavier) rotor blades, a small amount of elevator pre compensation may 
be needed to keep the nose of the helicopter flat at all times during col-
lective pitch changes.  In most cases with helicopter high-speed servos 
and standard 3D rotor blades, this function is not needed.  If you do notice 
a slight tendency for the nose to try to rise or fall with collective input, in-
creasing "ELE Comp" will reduce this behavior.

Setting ranges:  0 ~ 100%     Initial value: 0%

(8) HP. Auth.: High pitch authority    

When a rotor blades angle of attack is increased, the rotor blade becomes 
less reactive, in turn the helicopter might not feel as reactive at high pitch 
angles.  If you want to increase the reaction of the cyclic during loaded and 
high pitch maneuvers, "HP. Auth" will increase control authority and can be 
used to make the helicopter feel more linear under loading.  Some helicop-
ters with direct link CCPM may use this to increase stability at high collec-
tive pitch flying as well.  If a helicopter feels good for normal flying, but not 
the same during loaded situations, "HP. Auth" can be used to make it feel 
more linear.  If "HP. Auth" is set very high, the helicopter will feel more ag-
gressive at high pitch than around neutral.

Setting ranges:  0 ~ 100%  Initial value: HP. Auth = 0%

Cond

Summary of Contents for 01000141


































































































































































































































Reviews:

No comments

Related manuals for 01000141

Eaton PKE-COM-RTU Instruction Leaflet preview
PKE-COM-RTU
Brand: Eaton Pages: 2
Eaton i-on30R Installation Instructions preview
i-on30R
Brand: Eaton Pages: 2
Eaton MEMSHIELD 4 Installation Instructions Manual preview
MEMSHIELD 4
Brand: Eaton Pages: 8
GCE S 400 Operating Instructions Manual preview
S 400
Brand: GCE Pages: 24
PACH & COMPANY AeGIS 4000 Quick Installation And Programming Manual preview
AeGIS 4000
Brand: PACH & COMPANY Pages: 4
Insignia NS-GPS4RC101 Quick Setup Manual preview
NS-GPS4RC101
Brand: Insignia Pages: 2
Coris OMM-120-15 Quick Start Manual preview
OMM-120-15
Brand: Coris Pages: 4
Festool MS6-SV-...-D-10V24 Operating Instructions Manual preview
MS6-SV-...-D-10V24
Brand: Festool Pages: 32
SOMFY Situo 1 RTS Quick Installation Manual preview
Situo 1 RTS
Brand: SOMFY Pages: 56
Ultra Start 1655XR Owner'S Manual preview
1655XR
Brand: Ultra Start Pages: 12
Leggett & Platt G-SMR-2 CUSTOM Operation Manual preview
G-SMR-2 CUSTOM
Brand: Leggett & Platt Pages: 20
H3C VCF Installation Manual preview
VCF
Brand: H3C Pages: 16
Yale Z-Wave Plus v2 Installation Manual preview
Z-Wave Plus v2
Brand: Yale Pages: 2
Zander Aachen ZX20T Operating Manual preview
ZX20T
Brand: Zander Aachen Pages: 44
4D systems gen4-uLCD-35D Quick Start Manual preview
gen4-uLCD-35D
Brand: 4D systems Pages: 6
Defort DPS-17N User Manual preview
DPS-17N
Brand: Defort Pages: 92
Zamel EXTA LIFE P-520 Manual preview
EXTA LIFE P-520
Brand: Zamel Pages: 10
BLACKMER AVC Instructions And Parts List preview
AVC
Brand: BLACKMER Pages: 8

Brands by name

Popular brands

Load more brands