FUTABA 01000141 Full Manual Download Page 107

Page: 107 / 225

107

Tap here and go to the

Servo 2 settings page.

(Display and settings

content is the same as

Servo 1.)

When the Alarm or

Vibrator options are

activated, the servo

connection will

display.

*This alarm and display is limited to the S.BUS

servos connected to the servo sensors.

Tapping this will

take you to the

settings screen for

the current alarm

Telemetry : Servo sensor [Current]

The SBS-01S can monitor and display the in-flight

current, operating angle, and internal temperature

of up to two S.BUS2 servos.

If you forget to connect the servo wiring during

fuselage assembly, or the servo was disconnected,

an alarm can be activated at the transmitter.

*Servo sensor must be installed in the aircraft.

● Select [Servo sensor] in the Telemetry

screen and access the setup screen

shown below.

Max. and min. values

s i n c e t h e p o w e r

was turned ON will

display.

Sets the current on

which the alarm

operates.

Alarm is chosen from

Buzzer, Voice, and

Inhibit.

Allows Speech to be

turned ON or OFF.

Vibrator is choices are

type1-3, and Inhibit.

↑ An upward arrow

indicates the alarm

will sound when the

current reaches above

your set value.

↓ A downward arrow

indicates the alarm

will sound when the

current reaches below

your set value.

Initial value: ↑ 10.0A ↓ 0.0A

Adjustment range 0.0A~10.0A

( ↑ Limit ≧ ↓ Limit)

●Return to Linkage menu

Tapping this and selecting

"Buzzer" will cause the device

to sound an alarm when

servos are not connected.

Tapping this and selecting

"Each type" will cause the

device to vibrate when servos

are not connected.

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands