manualshive.com logo in svg

FUTABA 01000141, Full Manual

FUTABA 01000141 is a revolutionary product designed for convenience and efficiency. With its full manual available for download, users can easily access the comprehensive instructions they need to make the most out of their purchase. This manual can be downloaded for free from manualshive.com, ensuring hassle-free and user-friendly experience.

Share
Download
background image

216

Hysteresis-type and box-type can be selected in a hardware select screen.

◆ Linear・Hysteresis mode

◆ Symmetry・Hysteresis mode

◆ Linear・Box mode

When a stick, trim lever, or VR is used as a switch,

 

the following 4 modes can be selected.

This setting method selects function ON/OFF based 

on the set point. Hysteresis (dead band) can be set 

to ON and OFF. The ON and OFF positions can be 

reversed with the Reverse button.

The operation is the same as the linear hysteresis 

mode, but left and right (up and down) operations are 

symmetrical about the neutral position. For example, 

when you want to switch DR1 with the aileron stick, 

when the stick is moved to the left or right, DR1 can 

be turned ON at the same left and right position.

This mode turns on the switch within a range of 2 points. 

Each point can be set. The ON and OFF positions can be 

reversed with the Reverse switch.

◆ Symmetry・Box mode

The operation is the same as the linear box mode,
but  left  and  right  (up  and  down)  operation  is 

symmetrical about the neutral position.

Summary of Contents for 01000141


































































































































































































































Reviews:

No comments

Related manuals for 01000141

Aalborg DPC Operating Manual preview
DPC
Brand: Aalborg Pages: 128
MADRIX AURA Technical Manual & Quick Start Manual preview
AURA
Brand: MADRIX Pages: 36
Faulhaber MC 5004 Technical Manual preview
MC 5004
Brand: Faulhaber Pages: 66
Samson 3277 Mounting And Operating Instructions preview
3277
Brand: Samson Pages: 48
IFM CR710S Original Operating Instructions preview
CR710S
Brand: IFM Pages: 49
National Instruments NI cRIO-9036 User Manual preview
NI cRIO-9036
Brand: National Instruments Pages: 40
National Instruments cRIO-9063 Manual preview
cRIO-9063
Brand: National Instruments Pages: 28
National Instruments NI PXI-8104 Installation Manual preview
NI PXI-8104
Brand: National Instruments Pages: 7
National Instruments NI PXI-8840 Getting Started Manual preview
NI PXI-8840
Brand: National Instruments Pages: 22
UniPOS VIT 01 Instruction Manual preview
VIT 01
Brand: UniPOS Pages: 51
Unipulse F159 Operation Manual preview
F159
Brand: Unipulse Pages: 126
YachtSafe W010 Manual preview
W010
Brand: YachtSafe Pages: 3
Raynor Smart Control Panel 880RGD Quick Manual preview
Smart Control Panel 880RGD
Brand: Raynor Pages: 4
Paradox Esprit 727 Installation Instructions Manual preview
Esprit 727
Brand: Paradox Pages: 6
2gig Technologies Vario Installation Instructions Manual preview
Vario
Brand: 2gig Technologies Pages: 6
Linak CBH Advanced User Manual preview
CBH Advanced
Brand: Linak Pages: 33
Topway LMT070DICFWD-NJN User Manual preview
LMT070DICFWD-NJN
Brand: Topway Pages: 34
Anilam 4200T CNC Manual preview
4200T CNC
Brand: Anilam Pages: 31

Brands by name

Popular brands

Load more brands