manualshive.com logo in svg

FUTABA 01000141, Full Manual

FUTABA 01000141 is a revolutionary product designed for convenience and efficiency. With its full manual available for download, users can easily access the comprehensive instructions they need to make the most out of their purchase. This manual can be downloaded for free from manualshive.com, ensuring hassle-free and user-friendly experience.

Share
Download
background image

53

The System menu sets up functions of the 

transmitter. This does not set up any model data.

● When the System menu button is tapped, 

the menu shown below is called up. Tap the 

function button that you want to enter.

SYSTEM MENU

System menu functions table

Display

Display adjustment.

Sound  volume

Adjust the volume of: Other sound, Warning, Voice

System timer

Resets the system timer.

H/W setting

Stick mode selection (Mode 1 - Mode 4 ). J1-J4 sticks correction can be performed. 

Battery

Battery alarm voltage setting. Auto power off time setting.

Range check

The output of the transmitter is lowered, for Range checking.

S.Bus servo

S.Bus servo setting.

Information

Sets the User name, Language, and Unit system. Displays the program version, and micro SD card information.

●Return to Home screen

Summary of Contents for 01000141


































































































































































































































Reviews:

No comments

Related manuals for 01000141

Valve Concepts 3200 Installation, Operation And Maintenance Manual preview
3200
Brand: Valve Concepts Pages: 15
Panasonic FP0 Series Specifications preview
FP0 Series
Brand: Panasonic Pages: 27
Panasonic CZ-64ESMC2 Instruction Manual preview
CZ-64ESMC2
Brand: Panasonic Pages: 78
Panasonic GM1 Series Reference Manual preview
GM1 Series
Brand: Panasonic Pages: 98
NAiS FP0 Series Hardware Manual preview
FP0 Series
Brand: NAiS Pages: 173
Panasonic SL-VGU1-EC Instruction Manual preview
SL-VGU1-EC
Brand: Panasonic Pages: 2
Bartec MAK 3003 Manual preview
MAK 3003
Brand: Bartec Pages: 26
V2 CU1 Manual preview
CU1
Brand: V2 Pages: 48
D+H RZN 4503-T Instructions For Use Manual preview
RZN 4503-T
Brand: D+H Pages: 14
Jäger ADwin HSM-24V Manual preview
ADwin HSM-24V
Brand: Jäger Pages: 18
HQ Power VDPLC010 User Manual preview
VDPLC010
Brand: HQ Power Pages: 23
Joy-it Moto1 Quick Start Manual preview
Moto1
Brand: Joy-it Pages: 7
Woodward Vertex-Pro Installation/Hardware Manual preview
Vertex-Pro
Brand: Woodward Pages: 112
Danfoss VLT MCD 201 Installation Manual preview
VLT MCD 201
Brand: Danfoss Pages: 36
Ascon tecnologic vP4 Installation Manual preview
vP4
Brand: Ascon tecnologic Pages: 4
Eaton Char-Lynn 5 Series Manual preview
Char-Lynn 5 Series
Brand: Eaton Pages: 12
National Instruments NI 9503 C Series Getting Started preview
NI 9503 C Series
Brand: National Instruments Pages: 18
Bahco BBCE24-10 Manual preview
BBCE24-10
Brand: Bahco Pages: 150

Brands by name

Popular brands

Load more brands