manualshive.com logo in svg

FUTABA 01000141, Full Manual

FUTABA 01000141 is a revolutionary product designed for convenience and efficiency. With its full manual available for download, users can easily access the comprehensive instructions they need to make the most out of their purchase. This manual can be downloaded for free from manualshive.com, ensuring hassle-free and user-friendly experience.

Share
Download
background image

181

Swash Basic

Swash Basic

H-1

Swash Type

ELE

PIT

AIL

H3-120

ELE

PIT

AIL

H3-140

ELE

PIT

AIL

H3-90

ELE2

ELE

PIT

AIL

H4-00

ELE2

FRONT

ELE

PIT

AIL

H4-45

ELE

PIT

AIL

H-1

(4) SWASH Type: Swash change to plate type    

Select the swash plate type.  When you change the setting, other data is 
initialized.

Setting: H-1 / H3-120 / H3-140 / H3-90 / H4-00 / H4-45

　　　

Initial setting: H3-120

WARNING 

 All of the swash plate parameters are reset when the swash plate 

type is changed.  Doing so eliminates any possible errors or mal-
functions within the system. After changing the swash plate type, 
Please proceed through the entire setup process once again before 
attempting to fly the model.

AIL --------------------Aileron servo
ELE ----------------- Elevator servo
PIT ---------Collective pitch servo
ELE2 ---- Second elevator servo

Your transmitter should be reset to the default settings and the swash plate 
type selected with the transmitter should be set to "H-1" or single servo 
mode.  All CCPM mixing is set up and handled in the CGY, and the transmit-
ter functions should not be used.  Before starting model set-up, be sure that 
all dual rates, pitch curve, and endpoint values are set to 100/100. 

(5) Servo Dir #: Servo direction #   

Using different servo combinations will create the proper swash plate servo 
movement in electronic CCPM models (eCCPM).  In the H3-xx swash 
mode, three of the swash servos directions are changed by pressing the 
Servo Dir #.  Choose the combination number which produces level swash 
plate travel with a collective pitch input from the transmitter.  There are 8 
combination choices for the H3-xx swash mode.  On H4-xx swash mode, 
there are 16 combination choices.  After selecting the combination number, 
aileron, elevator, pitch, and 2nd elevator servo parameters are automati-
cally set.

Note:

 Occasionally the aileron or elevator function directions are reversed 

even though collective pitch direction is correct.  In this case, use the "SWS.
Dir parameter on the following screen (4/6) to fix this later.

Summary of Contents for 01000141


































































































































































































































Reviews:

No comments

Related manuals for 01000141

Campbell CELL200 Series Quick Deploy Manual preview
CELL200 Series
Brand: Campbell Pages: 3
rada 566 Installation And Maintenance Manual preview
566
Brand: rada Pages: 16
Lawler 805 Installation & Maintenance Manual preview
805
Brand: Lawler Pages: 5
Watlow F4T Installation And Troubleshooting User’S Manual preview
F4T
Brand: Watlow Pages: 59
Watts Tekmar WiFi Snow Melting Control 670 Installation Manual preview
Tekmar WiFi Snow Melting Control 670
Brand: Watts Pages: 48
Watts 009 Series Operation, Installation, Maintenance And Repair Manual preview
009 Series
Brand: Watts Pages: 8
G-Force UNDER CONTROL CP-30A PILOT User Manual preview
UNDER CONTROL CP-30A PILOT
Brand: G-Force Pages: 2
GBD BE24G Installation Instructions Manual preview
BE24G
Brand: GBD Pages: 60
YASKAWA Z1000 CIMR-ZU*A Series Programming Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 340
ETC Echoflex ELED2 Installation Manual preview
Echoflex ELED2
Brand: ETC Pages: 8
tell Compact-GSM Installation And Application Manual preview
Compact-GSM
Brand: tell Pages: 11
Moeller F&G Xcomfort CRCA-00/02 Assembly Instructions preview
F&G Xcomfort CRCA-00/02
Brand: Moeller Pages: 4
S.E.A. Group Sundstrom SR307 Manual preview
Sundstrom SR307
Brand: S.E.A. Group Pages: 5
Simpnic IRB-01-SW Quick Installation Manual preview
IRB-01-SW
Brand: Simpnic Pages: 16
Intellitec iConnex User Manual preview
iConnex
Brand: Intellitec Pages: 16
Paradox MG-RCV3 Reference And Installation Manual preview
MG-RCV3
Brand: Paradox Pages: 28
Belkin LiveAction User Manual preview
LiveAction
Brand: Belkin Pages: 60
claber Aqua Wireless 8347 Manual preview
Aqua Wireless 8347
Brand: claber Pages: 172

Brands by name

Popular brands

Load more brands