FUTABA 01000141 Full Manual Download Page 94

Page: 94 / 225

Telemetry: Receiver [Ext. battery]

Alarm set

1. Tap Alarm and choose from Buzzer, Voice,

and Inhibit.

2. Choose "Inhibit" for Vibrator if no

using the

vibrator alarm. If using vibrator, choose one

of the three types.

3. Tap to the Limit [4.0 V] item.

4. Adjust the rate using the "▼▼" "▼" "▲" "▲▲"

buttons.

Initial value: 4.0 V
Adjustment range: 0.0 V~100.0 V

*When the screen is tapped for one second, the rate is reset

to the initial value.

5. To terminate the input and return to the

original state, push the HOME/EXIT button.

Ext. battery

voltage

Sets the voltage on

which the alarm

operates.

↓ The "down" arrow

will indicate that an

alarm will sound when

the voltage drops to

below the setting.

Alarm is chosen from

Buzzer, Voice, and

Inhibit.

Allows Speech to be

turned ON or OFF.

● Tap the [Receiver] button in the Telemetry screen

to call the setup screen shown below.

Max. and min. values

since the power

was turned ON will

display.

Type 1

Type 2

Type 3

"Vibrator" type

If the following types are selected, the transmitter

will vibrate during the warning.

Displaying data from the EXT

battery voltage port

The EXT-VOLT screen will display the data from

the EXT-battery output from the R7108SB receiver.

In order to use this function, it is necessary to

connect external voltage connector of the R7108SB

receiver to a CA-RVIN-700 or SBS-01V to the

battery you desire to measure the voltage of the

EXT-battery

You will be alerted by an alarm or vibration if the

voltage set by you is exceeded.

*It cannot be used in FASST mode and S-FHSS mode.

*Only receiver voltage and EXT voltage can be used in

FASSTest12CH mode.

*The FASSTest18CH /T-FHSS mode can use all the telemetry

functions.

*CA-RVIN-700 must be installed in the aircraft.

●Return to

Linkage menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands