FUTABA 01000141 Full Manual Download Page 17

Page: 17 / 225

Touch Display

HOME/EXIT and U.MENU/MON.

Tap the panel with your finger to navigate.

*Plastic film is attached to the Touch Display. Please

be careful so that you don't scratch the Touch

Display with anything hard such as a metal object.

Don't push the Touch Display with excessive force

or drop anything on the panel.

*Although you may find some air bubbles under the

plastic panel due to environmental changes such

as temperature, it is not a defect and will cause no

problems.

*Color LCD is made from many pixels. Some

pixels hold lighting. Moreover, some pixels go out.

And a screen may flicker. Such condition is the

characteristics of color LCD. It is not failure.

Tapping the settings buttons for

each value on the settings screen

will cause value input buttons to

appear at the top of the panel.

Value input buttons display at the

top of the display.

Pressing and holding a value will

return it to its default setting.

Small change

in value

Large change

in value

Large change

in value

HOME/EXIT

Press

Return to the

previous screen

Press and hold Return to the

home screen

Press from

HOME screen.

To Telemetry

display

Press and hold

from HOME

screen.

Panel lock / Lock

release

Press

To user menu

display

Press and

hold

To servo monitor

display

U.MENU/MON.

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands