FUTABA 01000141 Full Manual Download Page 38

Page: 38 / 225

System mode

• System(FASSTest18CH etc.)

Type is displayed here.

Battery voltage for receivers

• In FASSTest/T-FHSS mode, this

data displayed. RX voltage

and Ext voltage display

The reception of the signal from the

receiver to the transmitter is shown.

• This does not affect flight.

Timer1, Timer2

• Timer is displayed here.
Tap the time button to start/stop the

timer. (When the screen is tapped for

1 second, timer is reset to the initial

value.)

Home Screen

Digital trim (T1 to T4)

• Trim position is displayed

here.

Model Name

• The model name that

is currently used is

displayed here.

RF Indicator

User's name

System timer

• This shows the accumulated time

since the latest reset. (Each model /

Total)
(Hour):(Minute):(Second)

This is the Home screen and descriptions of its menus. Use your finger to operate the touch screen.

→ (Menu)

• Model menu
Tap the Icon to call Model

Menu screen.

→ (Menu)

• System
• Linkage
• Model select
Tap the button to call each Menu

screen.

Battery Indicator

• When battery is low, the alarm

will beep. Land your aircraft

immediately.

Condition name

• The condition name

that is currently used

is displayed here.

WARNING

Be sure to confirm the model name before flying your aircraft.
Check the battery voltage as often as possible and try to charge the battery earlier.

If the battery alarm makes a sound, land your aircraft immediately.

*You can adjust the LCD contrast by the display setting in the system menu.

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands