FUTABA 01000141 Full Manual Download Page 136

Page: 136 / 225

136

RUDDER 2

RUDDER

V-TAIL

RUDDER 2

Winglet

RUDDER 1

Winglet

at Flying wing

( )

AIL 3

(Chip Aileron)

AIL1

(Main Aileron)

AIL 2

(Main Aileron)

Rudder → Aileron

[Corresponding model type]:

Airplane/glider, general

This function is used when you want to mix the

ailerons with rudder operation. It is used when

rudder is applied during roll maneuvers, knife

edge, etc. of acrobatic planes. It can be used to

bank scale models, large models, etc. like a full

size plane.

● A mixing curve can be set.

● Mixing during flight can be turned ON/OFF by

setting a switch. (Always ON at [--] setting)

● Linking can be set: Link this mix to other mixes.

● The mixing rate can be fine-tuned by setting a VR.

Setting method

● Tap [INH].

(ON is displayed.)

● When setting a switch, tap to the [--] item

of the switch and tap the screen to call the

selection screen. Then, select the switch and

set its ON direction. (Always ON at "--" setting)

(For a description of the switch selection

method, see back of this manual.)

● When setting a VR, tap to the Fine tuning

"--" item and tap the screen to call the

selection screen and then select the VR. The

adjustment rate can be set.

The VR operation mode can also be set.

(For a description of the fine tuning VR setting

method, see the description at the back of

this manual.)

● A mixing curve can be set.

(For a description of the curve setting

method, see the back of this manual.)

● When linking: tap the [Link] item. (ON is

displayed.)

Currently selected condition name

● Mixing curve setting

(For a description of the

setting method, see the

description at the back

of this manual.)

Left/right overall

adjustment at Rate A

and Rate B

Activate the function by

tapping the [INH].

Condition group/single

mode selection (Gr. /Sngl)

The ON/OFF switch of

mixing is chosen.

Fine tuning

setting

● Select [Rudder→Aileron] at the model menu

and call the setup screen shown below.

To set linking, tap to

the [OFF] item

●Return to Model menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands