FUTABA 01000141 Full Manual Download Page 102

Page: 102 / 225

102

Telemetry: Voltage [Ext. battery]

Alarm set

1. Tap Alarm and choose from Buzzer, Voice,

and Inhibit.

2. Choose "Inhibit" for Vibrator if no

using the

vibrator alarm. If using vibrator, choose one

of the three types.

3. Tap Limit [4.0 V].

4. Adjust the rate using the "▼▼" "▼" "▲" "▲▲"

buttons.

Initial value: 4.0 V
Adjustment range: 0.0 V~100.0 V

*When the screen is tapped for one second, the rate is reset to

the initial value.

5. To terminate the input and return to the

original state, push the HOME/EXIT button.

Sets the voltage on

which the alarm

operates.

↓ The "down" arrow

will indicate that an

alarm will sound when

the voltage drops to

below the setting.

Alarm is chosen from

Buzzer, Voice, and

Inhibit.

Allows Speech to be

turned ON or OFF.

● Tap the [Voltage] button in the Telemetry screen to

call the setup screen shown below.

Max. and min. values

s i n c e t h e p o w e r

was turned ON will

display.

Type 1

Type 2

Type 3

"Vibrator" type

If the following types are selected, the transmitter

will vibrate during the warning.

Displaying data from the EXT

battery voltage port

In this screen, the EXT battery voltage is

displayed.

In order to use this function, it is

necessary to connect External voltage connector of

R7108SB

⇔

SBS-01V

⇔

Battery

SBS-01V measures two batteries. The power

battery connected to two lines is displayed on EXT-

VOLT.

*SBS-01V must be installed in the aircraft.

*It cannot be used in FASST mode and S-FHSS mode.

*Only receiver voltage and EXT voltage can be used in

FASSTest12CH mode.

*The FASSTest18CH /T-FHSS mode can use all the telemetry

functions.

Ext. battery

voltage

●Return to

Linkage menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands