manualshive.com logo in svg

FUTABA 01000141, Full Manual

FUTABA 01000141 is a revolutionary product designed for convenience and efficiency. With its full manual available for download, users can easily access the comprehensive instructions they need to make the most out of their purchase. This manual can be downloaded for free from manualshive.com, ensuring hassle-free and user-friendly experience.

Share
Download
background image

99

Vario Melody Setting

Tap the [Set] button

Next page

Current variometer

This is the changing point of climb and sink. When the variometer 
is greater than this value, Vario Melody is climb type. When the 
variometer is less than this value, Vario Melody is sink type.

Setting range

：

Range ↑ setting value 

～

 Range ↓ setting value

Initial value

：

0.0 m/s

When the variometer is less 
than this value, Vario melody 
is not output.

Setting range

：

                                

0 m/s

～

 +50 m/s

Initial value

：

0.0 m/s

W h e n  t h e  v a r i o m e t e r  i s 
greater than this value, Vario 
melody is not output.

Setting range

：

                             

-50 m/s

～

0 m/s

Initial value

：

0.0 m/s

When the variometer is less than 
this value, Vario melody is not 
variable.

Setting range

：

-50 m/s

～

Offset value

Initial value

：

-5.0 m/s

When the variometer is greater 
than this value, Vario melody is 
not variable.

Setting range

：

Offset value

～

 +50 m/s

Initial value

：

5.0 m/s

*These settings can be 

made for each sensor.

[The relation of Vario Melody settings]

Dead band

（Not sound）

Fixed melody

Fixed melody

Variable melody

Variable melody

Climb side

Discontinuous 

sounds

Sink side

Continuous

sounds

Range

↑

Deadband

↑

Deadband

↓

Range

↓

Offset

Offset

Deadband

Range

Summary of Contents for 01000141


































































































































































































































Reviews:

No comments

Related manuals for 01000141

Jafar 2911 Operation And Maintenance Manual preview
2911
Brand: Jafar Pages: 10
Jafar 2911 Operating Manual preview
2911
Brand: Jafar Pages: 8
EA SV Series Original Operating Manual preview
SV Series
Brand: EA Pages: 24
3Ware 7000-2 - Escalade RAID Controller Features preview
7000-2 - Escalade RAID Controller
Brand: 3Ware Pages: 2
easydriver Pro Installation And Instruction Manual preview
Pro
Brand: easydriver Pages: 26
Calsense CS3000 Quick Start Manual preview
CS3000
Brand: Calsense Pages: 10
Zeagle Razor Service Manual preview
Razor
Brand: Zeagle Pages: 37
Hanna Instruments HI 8001 Instruction Manual preview
HI 8001
Brand: Hanna Instruments Pages: 88
Parker AC890PX Series User Mounting And Assembly Instructions preview
AC890PX Series
Brand: Parker Pages: 30
Parker Compax3M Series Installation Manual preview
Compax3M Series
Brand: Parker Pages: 52
Parker AC30V Series Manual preview
AC30V Series
Brand: Parker Pages: 337
Xylem FST Installation, Operation And Maintenance Manual preview
FST
Brand: Xylem Pages: 48
Abocom AM7221 User Manual preview
AM7221
Brand: Abocom Pages: 10
Daruifuno MCC100 User Manual preview
MCC100
Brand: Daruifuno Pages: 24
Insignia NS-GPS4RC101 Quick Setup Manual preview
NS-GPS4RC101
Brand: Insignia Pages: 2
Scanreco G5 LP Instruction Manual preview
G5 LP
Brand: Scanreco Pages: 10
Teledyne Foxy R1 Instruction Manual preview
Foxy R1
Brand: Teledyne Pages: 102
LCT HQ-TJ-901 Operation Manual preview
HQ-TJ-901
Brand: LCT Pages: 5

Brands by name

Popular brands

Load more brands