manualshive.com logo in svg

FUTABA 01000141, Full Manual

FUTABA 01000141 is a revolutionary product designed for convenience and efficiency. With its full manual available for download, users can easily access the comprehensive instructions they need to make the most out of their purchase. This manual can be downloaded for free from manualshive.com, ensuring hassle-free and user-friendly experience.

Share
Download
background image

151

This section contains information on the commands 

that apply to helicopters only. For instructions 

on airplane, glider and multicopter, refer to the 

sections pertaining to those aircraft.

Use the Model type function in the Linkage menu 

to select the swash type matched to the fuselage 

beforehand.

Also, add flight conditions at the Condition Select 

screen if necessary before setting the model data at 

each function. (Up to 8 conditions can be used)

The AFR function, dual rate function and other 

functions common to all model types, are described 

in a separate section.

◆ Condition hold

When performing adjustments, such as idling up, when the engine is 

engaged, keep the throttle stable so as to prevent the engine from revving 

too high. Once your adjustments are complete, always make sure to set 

the function to [OFF].

*Condition hold ON/OFF operation is possible under normal conditions 

and the throttle stick is more than 1/3rd into the slow throttle range. 

Throttle servos will remain at the throttle stick position during ON 

operation.

● ON/OFF operation on the Home screen

Under the conditions described above, tap the Condition hold [OFF] 

displayed on the screen.

During function operation, Condition hold will display [ON] and an 

alarm will sound.

       WARNING

For safety reasons, when performing individual 

adjustments it is recommended that you shut off 

the engine and disconnect the motor to prevent 

rotation.  

*Sudden, abrupt rotation can result in death or serious injury.

MODEL MENU

 (Helicopter functions)

Model menu (Helicopter) functions table

Servo monitor

Displays the servo test and operation position

Condition select

Flight conditions addition, deletion, copy, condition renaming, and condition delay can be set. 

AFR

Sets the angle and curve of all the operation functions. 

Dual rate

D/R curve which can be switched with a switch, etc. can also be added.

Program. mixes

Program mixing which can be freely customized. Up to 10 mixes can be used for each condition.

Pitch curve

Pitch curve and hovering trim adjustment

Throttle curve

Throttle curve and hovering trim adjustment

Acceleration

Allows a brief "overload" in response to sudden throttle and pitch commands

Throttle hold

Moves the throttle to idle during autorotation

Swash mixing

Compensates for each control response

Throttle mixing

Compensates for power loss when cyclic applied

Pitch → Needle

Adjusts response curve in different flight conditions

Pitch → Rudder

Handles torque changes from pitch angle inputs

Gyro

Used to switch gyro sensitivity

Governor

Used to switch RPM of the helicopter’s head

Gyro setting

Detailed setting of CGY755/CGY760R

Summary of Contents for 01000141


































































































































































































































Reviews:

No comments

Related manuals for 01000141

Waters 2690 Quick Start Manual preview
2690
Brand: Waters Pages: 55
Paradox IP150 Programming Manual preview
IP150
Brand: Paradox Pages: 2
easydriver Pro Installation And Instruction Manual preview
Pro
Brand: easydriver Pages: 26
Calsense CS3000 Quick Start Manual preview
CS3000
Brand: Calsense Pages: 10
Yardney Synergy Quick Start Manual preview
Synergy
Brand: Yardney Pages: 8
Fagor CNC 8070 Original Instructions Manual preview
CNC 8070
Brand: Fagor Pages: 10
Fagor CNC 8070 Operating Manual preview
CNC 8070
Brand: Fagor Pages: 358
Fagor CNC 8070 Programming Manual preview
CNC 8070
Brand: Fagor Pages: 556
Fagor CNC 8060 Operating Manual preview
CNC 8060
Brand: Fagor Pages: 172
Fagor CNC 8060 Translation Of The Original Manual preview
CNC 8060
Brand: Fagor Pages: 180
Fagor CNC 8060 Hardware Configuration preview
CNC 8060
Brand: Fagor Pages: 112
FaderMate Master Control Unit Fittings Manual preview
Master Control Unit
Brand: FaderMate Pages: 36
Yamaha RCX340 Service Information preview
RCX340
Brand: Yamaha Pages: 5
Yamaha ACD1 Owner'S Manual preview
ACD1
Brand: Yamaha Pages: 20
Yamaha DCP4S-EU Owner'S Manual preview
DCP4S-EU
Brand: Yamaha Pages: 2
Zennio KLIC-DI User Manual preview
KLIC-DI
Brand: Zennio Pages: 30
Zeta PREMIER EX8 User Manual preview
PREMIER EX8
Brand: Zeta Pages: 13
Aulisa GA-AP0011 Instructions For Use Manual preview
GA-AP0011
Brand: Aulisa Pages: 32

Brands by name

Popular brands

Load more brands