FUTABA 01000141 Full Manual Download Page 64

Page: 64 / 225

● Tap the [Model select]

button in the Home

screen to call the setup

screen shown below.

＜ or ＞

Current model is

green.

Model select

The Model selection function performs model addition, call,

deletion, copy, and model name setting.

This function is used to load the settings of the

desired model into the T16IZ’s memory.

The settings may be selected from either the

transmitter’s built-in memory. Remember that up to

30 model memories are available in the transmitter.

The model data of the SD card is for storage. SD

card model data cannot be called directly from the

transmitter. The name of the model stored in the

transmitter and the SD card may be changed. This

can be very useful to tell different models settings

apart. Each model name can be as long as 15

characters, and the model name always appears in

the display screen.

The Copy function is used to copy one set of model

data into a second memory within the transmitter

and the SD card. It may be used for getting a head-

start on setting up models with almost the same

settings (only differences need to be modified,

instead of entering the complete model from

scratch). Also, this function may be used to make a

backup copy of a model setup before any changes

are made.

● Select [Model select] at

the linkage menu and

call the setup screen

shown below.

Model addition

1. Tap the [New] button.

2. Tap [Yes] to add the model. (When you want

to cancel model addition, tap [No].)

*The added model is displayed in the model list.

*When a model is added, a receiver link is required.

● "Save to"

[Internal]: transmitter

memory

[SD card]: SD card

●Return to Home or

Linkage menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands