FUTABA 01000141 Full Manual Download Page 36

Page: 36 / 225

S.BUS2 System

When using the S.BUS2 port, an impressive array of telemetry sensors may be utilized.

Receiver port

S.BUS Servo

S.BUS Gyro

S.BUS2

Servo

S.BUS2

Gyro

Telemetry sensor

S.BUS

○

S.BUS2

×　（※）

○

S.BUS2 TABLE

（※）Don't connect S.BUS Servo, S.BUS

Gyro to S.BUS2 connector.

S.BUS2

Port

S.BUS

Port

(8/SB)

Hub

Servo

S.BUS2

Servo

S.BUS Servo

S.BUS2

servo

Connection is possible

Mixed connection

S.BUS

and

S.BUS2

is possible.

S.BUS2

gyro

Connection is possible

S.BUS servo

Connection is impossible

Telemetry sensor

Connection is impossible

S.BUS2

GYRO

CH Mode is set

to ModeB [D].

＋

Telemetry

Sensors

S.BUS servos and gyros and S.BUS2 servos and gyros must be used in the correct receiver

ports. Please refer to the instruction manual to make sure you connect to the correct one.

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands