FUTABA 01000141 Full Manual Download Page 15

Page: 15 / 225

WARNING

Be careful not to drop the battery.

Never disconnect the battery connector

from the T16IZ transmitter after

turning off the power until the screen is

completely blank and the transmitter has

shut down completely.

* Internal devices such as memories may be damaged.

* If there is any problem, the message "Backup Error" will

be shown the next time when you turn on the power of the

transmitter. Do not use the transmitter as it is. Send it to the

Futaba service center.

WARNING

Do not plug and unplug the charger

when your hands are wet.

*It may cause an electric shock.

Do not overcharge/overdischarge the

battery.

*Overcharging/Overdischarging a battery can result in

burns, fire, injuries, or loss of sight due to overheating,

breakage, or electrolyte leakage.

CAUTION

When the charger is not in use,

disconnect it from the AC outlet.

* Do this to prevent accidents and to avoid overheating.

Charging a battery

Charging LED

Red: Charging
Green: Full

Use a commercially available

USB charger AC adapter

USB-A type 5 V-2 A

USB Cable

This set is not equipped with an AC adapter

for charging. Must be purchased separately.
● AC adapter USB-A type 5 V - 2 A

● Futaba option AC adapter USB type

Access the charge port by

flipping the rubber cover

on the bottom of the

transmitter.

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands