FUTABA 01000141 Full Manual Download Page 145

Page: 145 / 225

145

(Example) Setting three axis using a GYA450 and GYA451 (2)

● Wing type: Aileron 2 servos mounted fuselage selected
● Set

5CH → Gyro

(GYA451AIL),

7CH → Gyro2

(GYA451ELE),

8CH → Gyro3

(GYA450RUD),

Control and Trim → "--"

: at

the Function menu of the Linkage menu.

● Gyro setting of the Model menu.

*Set so that Rate 1 is turned on at the back position of switch E

and Rate 3 is turned ON at the front position. Since switch E is

turned OFF at the center, Rate 2 remains [INH].

Rudder servo

Elevator servo

Aileron servo

S.BUS2 port

S.BUS Receiver

GYA451

GYA450

GAIN 0％

AVCS

NORMAL

When AVCS is used we

recommend that the

sensitivity CH be set to

the 3-position.

Rate

ACT

Type

Switch

Gyro

Gyro ２

Gyro ３

OFF/ON

AVCS : 60%

INH

ON/OFF

Normal : 60%

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands