manualshive.com logo in svg

FUTABA 01000141, Full Manual

FUTABA 01000141 is a revolutionary product designed for convenience and efficiency. With its full manual available for download, users can easily access the comprehensive instructions they need to make the most out of their purchase. This manual can be downloaded for free from manualshive.com, ensuring hassle-free and user-friendly experience.

Share
Download
background image

192

Rudder Expert

Rudder Expert

The rudder Expert menu allows for further refinement of the tail rotor gyro performance. "Rudder Expert" screen from the "EXPERT MENU 

3D" screen.

(1) RUD Ntr: Rudder servo neutral setting          

This parameter is used to set the neutral position of the rudder servo.  Po-
sition the rudder servo arm as perpendicular as possible to the tail rotor 
pushrod prior to making adjustments with this parameter.

Setting ranges:  -240 ~ 0 ~ +240     Initial value: +0

(2) EXP. AVCS / EXP. NORM: Rudder exponential            

This parameter sets the feel of the tail rotor control around center.  When 
set to [0] the control curve is linear.  Using a [+] value the tail rotor will be 
more sensitive around neutral conversely, using a [-] value will soften the 
feeling around neutral.  The RUD EXP parameter in your transmitter can 
also be used to tune the tail rotor to a desired feeling.

Setting ranges:  -100 ~ 0 ~ +100%     Initial value: AVCS = -20%, NORM = -20%  

Sports = AVCS -60% / NORMAL -40%,  3D = AVCS -20% / NORMAL -20%>

Summary of Contents for 01000141


































































































































































































































Reviews:

No comments

Related manuals for 01000141

Jafar 2911 Operation And Maintenance Manual preview
2911
Brand: Jafar Pages: 10
Jafar 2911 Operating Manual preview
2911
Brand: Jafar Pages: 8
GARDTEC 800 User Instructions preview
800
Brand: GARDTEC Pages: 48
FAAC 740 D User Manual preview
740 D
Brand: FAAC Pages: 64
GBD BA100 Instructions For Installations preview
BA100
Brand: GBD Pages: 68
UNITED C5 Series Installation & Service Manual preview
C5 Series
Brand: UNITED Pages: 22
Danfoss VLT MCD 200 Installation Manual preview
VLT MCD 200
Brand: Danfoss Pages: 32
Danfoss PVG 16 PVH/Covers Technical Information preview
PVG 16 PVH/Covers
Brand: Danfoss Pages: 112
Danfoss PVG 100 Service And Parts Manual preview
PVG 100
Brand: Danfoss Pages: 44
Danfoss PVG 16 PVH/Covers Service And Parts Manual preview
PVG 16 PVH/Covers
Brand: Danfoss Pages: 144
Danfoss VLT LCP 11 Installation Instructions preview
VLT LCP 11
Brand: Danfoss Pages: 2
Danfoss VLT FC Series Operating Instructions Manual preview
VLT FC Series
Brand: Danfoss Pages: 64
Danfoss EKC 102A Instructions Manual preview
EKC 102A
Brand: Danfoss Pages: 8
Danfoss VLT AutomationDrive FC 360 Programming Manual preview
VLT AutomationDrive FC 360
Brand: Danfoss Pages: 60
Danfoss DHP-A Installation Instruction preview
DHP-A
Brand: Danfoss Pages: 6
Danfoss AMV 110 NL AQT Datasheet preview
AMV 110 NL AQT
Brand: Danfoss Pages: 4
Danfoss VLT FC Series Installation Manual preview
VLT FC Series
Brand: Danfoss Pages: 8
Danfoss AK-CC 550A Troubleshooting Manuallines preview
AK-CC 550A
Brand: Danfoss Pages: 2

Brands by name

Popular brands

Load more brands