FUTABA 01000141 Full Manual Download Page 124

Page: 124 / 225

124

● Tap the [Prog. mixes] button in the Model menu to call

the setup screen shown below.

Program. mixes

Program mixing which can be freely customized. Up to 10

mixings can be used for each condition. [All model types]

Programmable mixing may be used to correct

undesired tendencies of the aircraft, and it may also

be used for unusual control configurations. Mixing

means that the motion of a command channel,

called the "master," is added to the motion of the

mixed channel, called "slave."

You may choose to have the Masters trim added to

the Slave channel response, if you desire ("Trim"

setting). The mixing curve can be changed so

that the undesired tendencies can be corrected

effectively by setting the EXP1/EXP2/Point modes.

Offset-type mixing applies a fixed offset or preset

to the programmed channel servo operation and

may control up to four circuits simultaneously.

The Programmable mixing includes a powerful link

function, which allows Programmable mixing to be

linked with the special mixing functions, or with

other programmable mixing functions. The link

function can be set up for Master and Slave channel

individually.

Fine tuning trim

setting

The on time (start/stop

time) can be set up to 4

seconds. It is useful for

landing gear control of the

jet or scale plane, etc.

● Group/single mode

switch (Gr./Sngl)

(For more information,

see the description

at the back of this

manual.)

Mixing/Offset mode

switch

After this function is

activated, the master

and slave function

names (or offset mixing)

are displayed.

● Operation curve setting

(For a description of the

setting method, see the

description at the back of

this manual.)

Activate the function by

tapping the [INH] .

Trim mode setting ON/OFF.

The ON/OFF switch of

prog. mixes is chosen.

Master function

(or Stick, Switch, Dial)

is chosen.

Slave function is chosen.

Servo speed setting

●Return to Model menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands