FUTABA 01000141 Full Manual Download Page 34

Page: 34 / 225

Rubber

grommet

Brass eyelet

Wood screw

Servo mount

2.3-2.6mm nut

washer

Rubber

grommet
Brass eyelet

Servo mount

2.3-2.6mm screw

(Helicopter)

(Airplane/Glider)

Servo lead wires

To prevent the servo lead cable from being

broken by vibration during flight, provide a

little slack in the cable and fasten it at suitable

points. Periodically check the cable during daily

maintenance.

Fasten about 5-10cm

from the servo outlet so

that the lead wire is neat

and secure.

Margin in the lead wire.

Mounting the power switch

*Switch is not included in this set.

When mounting a power switch to an airframe,

make a rectangular hole that is a little larger than

the total stroke of the switch so that you can turn

the switch ON/OFF without binding.

Avoid mounting the switch where it can be

covered by engine oil and dust. In general, it is

recommended to mount the power switch on the

side of the fuselage that is opposite the muffler.

Safety precautions when you

install receiver and servos.

WARNING

Connecting connectors

Be sure to insert the connector until it

stops at the deepest point.

How to protect the receiver from vibration and

water

Wrap the receiver with something

soft such as foam rubber to avoid

vibration. If there is a chance of

getting wet, put the receiver in a

waterproof bag or balloon.

Receiver's antenna

Never cut the receiver's antenna. Do

not bind the receiver's antenna with

the cables for servos.

Locate the receiver's antenna as far as

possible from metals or carbon fiber

components such as frames, cables,

etc.

*Cutting or binding the receiver's antenna will reduce the

radio reception sensitivity and range, and may cause a

crash.

Servo throw

Adjust your system so that pushrods

will not bind or sag when operating

the servos to the full extent.

*If excessive force is continuously applied to a servo, the

servo could be damaged due to force on the gear train

and/or power consumption causing rapid battery drain.

Mounting servos

Use a vibration-proof rubber (such as

rubber grommet) under a servo when

mounting the servo on a servo mount.

And be sure that the servo cases do

not touch directly to the metal parts

such as servo mount.

*If the servo case contacts the airframe directly, vibration

will travel to and possibly damage the servo.

Mounting the Servo

*Servo is not included in this set.

Switch

Less than 5 mm of
mounting plate

Attached screw

Switch cover

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands