FUTABA 01000141 Full Manual Download Page 127

Page: 127 / 225

127

FLP 2

(Camber Flap)

FLP 1

(Camber Flap)

FLP 3

(Brake Flap)

FLP 4

(Brake Flap)

Flap setting

[Corresponding model type]: Airplane/

glider, 2 flaps or more]

The up/down travel of each flap (camber flaps:

FLP1/2, brake flaps: FLP3/4) can be adjusted

independently at each servo according to the wing type.

● The operation reference point of each flap can be

offset

The camber flaps of a 4-flap model can be mixed

with the brake flaps. (Brake FLP to camber FLP)

● An ON/OFF switch can be set.

Setting method

● Tap flap (FLP) 1~4 up or down according to

the wing type.

Adjust the travel independently.

● To offset the operation reference point of

each flap, tap the corresponding offset item.

Use the "▼▼" "▼" "▲" "▲▲" button to offset

the reference point.

● When using brake FLP to camber FLP mixing,

tap the [INH] item and tap the screen. (ON is

displayed.)

When setting a switch, tap the [--] item of

the switch and tap the screen to call the

selection screen. Then, select the switch and

set its ON direction. (Always ON at "--" setting)

(For a description of the switch selection

method, see the description at the back of

this manual.)

Camber flap setting

Brake flap setting

● Select [Flap setting] at the model menu and

call the setup screen shown below.

*The display screen is an

example. The actual screen

depends on the Model

Type.

Condition group/single

mode selection (Gr. /Sngl)

(For more information, see

the description at the back

of this manual.)

Currently selected condition name

Brake flap to Camber flap setting

Operation reference

point offset

Operation reference

point offset

Up side/Down side

adjustment

Up side/Down side

adjustment

The ON/OFF switch of

mixing is chosen.

Mixing

INH ⇔ ON

Operation is performed via the volume

switches, etc., set for each flap control of the

function.

The operational volume

switch is set up by "Function"

●Return to Model menu

Summary of Contents for 01000141


































































































































































































































Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands

FUTABA 01000141, Full Manual

Search results

Summary of Contents for 01000141

Reviews:

Related manuals for 01000141

Brands by name

Popular brands